lifting equipment

view basket - lifting equipment and safety equipment online shop

Phone +44(0)1724 711043

Email sales@lifting-safety.co.uk

Section Clamps

Bulb Bar Section Clamp Type CB

Bulb Bar Section Clamp Type CB

The Camlok Bulb Bar Section Clamp was designed specifically for lifting and handling bulb bar sections or fabrications containing bulb bar sections. The clamp is almost exclusively used in the ship building industry. The clamp is supplied as standard with a hook ring as shown in the illustration this can however be replaced with an integral short chain sling for direct connection to the hook of the lifting appliance. The clamp is fitted with a Camlok spring operated safety lock.

Model WLL
Tons
Bulb
mm
Weight kg
 
CB0.75 0.75 40 6
CB1.5 1.5 60 12
CB3.0 3.0 83 32
CB4.0 4.0 83 42
CB6.0 6.0 83 44
CB8.0 6.0 5-75 46
CB10 10.0 87 57

Girder Clamp Type CG

Girder Clamp Type CG

The Camlok CG Clamp is designed to lift and transport rolled steel joists in the vertical position. The clamp is designed to land the beam in either the vertical or horizontal position. The clamp is fitted with a cam/spring operated safety lock. Long lengths of beam should be lifted with 2 clamps supported from a lifting beam.

Model WLL
Tonnes
Plate Thickness
mm
Weight
Pair kg
 
CG1 1 0-16 6
CG2 2.0 0-32 14
CG4 4.0 0.32 19
CG6 6.0 12-50 37
GC8 8.0 12-50 40

Girder Clamp (Horizontal) Series TTR

Girder Clamp (Horizontal) Series TTR

The TTR Series of Clamps have been designed to lift and transport structural steel beams in the horizontal position i.e. with the flanges in the vertical position. The clamp is designed with the hook ring as near as to the centre of gravity of the beam as possible, thus resulting in a near horizontal lift. Long beams should be lifted using 2 clamps attached to opposite beam flanges. The clamp is fitted with a Camlok spring/cam operated safety lock.

Model WLL
Tonnes
Flange
mm
Weight kg
 
TTR0.75 0.75 5-16 3
TTR1.5 1.5 5-25 8
TTR3.0 3.0 5-28 13

Girder Clamp (Vertical) series TTG

Girder Clamp (Vertical) series TTG

The TTG Girder Clamp is designed to lift and transport structural steel beams in the vertical position i.e. with the flanges in the horizontal position. The clamp is fitted with a Camlok spring operated safety lock and is operated by pulling the locking handle upwards. Long beams should be lifted with 2 clamps attached on opposite beam flanges, the clamps supported from a lifting beam.

Model WLL
Tonnes
Flange
mm
Weight kg
 
TTG1.5 1.5 0-30 5
TTG3.0 3.0 0-35 10/td>
TTG4.5 4.5 0-40 14
TTG7.5 7.5 0-45 27

Girder Clamp (Vertical) series TTT

Girder Clamp (Vertical) series TTT

The TTT Series Clamp is a variant of our TTG clamp this clamp is designed to be used in pairs supported from a 2 legged chain sling. The bottom toe plate is split thus enabling the clamp to be attached to the end of the structural steel beam. The clamp is fitted with a spring operated safety lock. The clamp is particularly useful for erecting structural beams on construction/building sites.

Model WLL
Tonnes
Flange
mm
Weight kg
 
TTT0.75 0.75 0-20 3
TTT1.5 1.5 0-35 6
TTT3.0 3.0 0-40 10
TTT4.5 4.5 0-45 16

For further information or to request a quotation please contact
sales@lifting-safety.co.uk

To assist us in responding quickly to your enquiry please always include relevant information on your enquiry such as SWL, Height of Lift and where required Electricity phase.

Thank You



Home | About | Lifting Equipment | Services | News | Special Offers | Contact Us | Online Shop | Site Map
lifting equipment