Verticle Plate Clamps

Vertical Plate Clamps Series 92

The CZ92 Series Universal Clamp has been designed and developed after extensive research and field testing. This non-welded clamp incorporates many innovative design features. The jaw and pad incorporate a triangular shaped wear indicator. These components should be replaced when serrated teeth wear down flush with wear indicator. The standard clamp is fitted with a hook ring and a cam operated locking mechanism, however if preferred the hook ring can be replaced with a short length of chain and master link and the cam operated locking mechanism can be replaced with a chain pull mechanism. The pad and jaw are manufactured from high grade heat treated steel and are suitable for all structural steel up to 300 Brinell Surface Hardness.Please contact our sales/technical department if the plate to be lifted has a higher surface hardness.

NOTE: The CZ920.5 clamp is supplied without a locking lever.

Vertical Plate Clamps Series CY92

The CY Non-welded Hinged Universal Clamp is a variant of our successful CZ92 Series Clamp. The clamp has all the innovative design features of the CZ92 clamp and incorporates a hinged hook ring. This device enables the clamp to be used at any angle thus permitting awkward lifts previously considered hazardous. The standard clamp is fitted with a cam operated locking mechanism but this can be replaced (at no additional cost) by a chain pull locking mechanism . The CY range is fitted with hardened steel pads and jaws that incorporate tooth wear indicators. The clamp is designed to lift and handle plate with a surface hardness up to 300 Brinell. Contact our sales/technical department if plate to be lifted has a higher surface hardness. Other clamps in our range are available for this application.

The Camlok CZ Series Vertical Plate Clamp

This differs from our CZ92 series in that the body of the clamp is a welded construction. The series has a lifting capacity range of 1 to 30 tons. The CZ series clamp can be used to lift plate from the horizontal to vertical position and vice versa. This clamp series is suitable for handling steel plate with a surface hardness of up to 300 Brinell. The standard clamp is fitted with a hook ring this can be replaced with a short length of chain and master link. The clamp can be supplied with alternative body shapes, please click on the 'options' button below for details. Clamp jaws and pads are manufactured from high tensile steel and have heat treated serrated teeth.

The Camlok CX Hinged Series Vertical Plate Clamp
This differs from our CZ92 series in that the body of the clamp is a welded construction. The series has a lifting capacity range of 1 to 30 tons. The CZ series clamp can be used to lift plate from the horizontal to vertical position and vice versa. This clamp series is suitable for handling steel plate with a surface hardness of up to 300 Brinell. The standard clamp is fitted with a hook ring this can be replaced with a short length of chain and master link. The clamp can be supplied with alternative body shapes, please click on the 'options' button below for details. Clamp jaws and pads are manufactured from high tensile steel and have heat treated serrated teeth.

Series T Wide Mouth Plate Clamps

The Camlok Type “T” Wide Mouth Clamp is designed to lift and handle thick section plate and components. The horizontal gripping force is transmitted to the load being lifted via a grade 80 chain and chain rollers. The clamp is opened by pulling down on the lever attached to the moving jaw. The clamp is suitable for lifting thick plate from the horizontal to vertical position and vice versa. The clamp design is versatile and can be easily modified to suit loads of virtually any width. Clamps with WLL’s of 2 tons and below are fitted with link chain as shown in the illustrations. The 3, 5 and 10 ton WLL clamps are supplied with roller chain. The standard clamps are supplied with moving jaw and fixed pad with serrated steel teeth, these can be replaced with jaw and pads fitted with rubber linings to minimise damage to the component being lifted

Series Hg Vertical Plate Clamps High Grip

The Camlok High Grip Clamp has an additional lever in the clamping mechanism thus asserting a very high gripping force on the plate being lifted. The clamp has been designed to lift plates with hardened surfaces and for stainless steel plates. The clamp is suitable for use with materials up to 376 Brinell surface hardness. Clamps can be used for lifting and turning plates from the horizontal to vertical or vice versa. The standard clamp is fitted with a hook ring but can alternatively be supplied with a short length of chain NOTE: Clamp will mark the surface of the material being lifted.

For further information or to request a quotation please contact
sales@lifting-safety.co.uk

To assist us in responding quickly to your enquiry please always include relevant information on your enquiry such as SWL, Height of Lift and where required Electricity phase.

Thank You