Hydraulic Accessories
|
 |
MY - Manifolds
700 bar
Manifolds are used when several hydraulic cylinders have to be connected to one hydraulic pump
|
|
 |
AYP - Threaded Flanges
700 bar, incl. pressure set valve
In case hydraulic cylinders have to be inserted into fixtures, press frames or similar devices, these steel flanges can be
very handy.
|
|
 |
Accessories for YS Cylinders - Lifting Claws
In connection with the corresponding hydraulic cylinder, a lifting
claw represents a compact, lightweight and versatile lifting unit.
Claws can be placed under loads with minimum clearance.
During the lifting operation, the cylincer must be supported against the load in order to eliminate unfavourable forces
caused by eccentric loading
|
|
 |
Accessories for YS Cylinders - Piston Plates
These can be screwed into the piston thread of cylinders series YS. They reduce the surface pressure and prevent the pistons
from sinking into the ground.
Also, when using a piston plate in connection with a lifting claw, the cylinder must be supported against the load.
Other YS Accessories include Base Adaptors & Extension Tubes andSupport Plates.
|
|
 |
HHC - Hydraulic Hoses
Durable but highly flexible thermoplast hydraulic hoses guarantee a very long life.
The four-layer build-up includes 2 layers of high tensile steel fabric and robust fitting with 19mm hexagon. The volumetric
expansion is very low.
Hydraulic hoses model HHC... are equipped with a male coupler half as standard. Standard lengths
are as the chart below, further lengths or hoses with larger diameters are quoted on request
|
| Standard Length |
0.5m, 1m, 2m, 3m, 4m, 5m, 6m, 8m, 10m, 12m, 15m |
| Safety Factor |
4:1 (burst pressure 2800 bar) |
| Bend Radius |
100mm |
| Nominal Width |
6.3mm |
|
 |
Hydraulic Couplers
Hydraulic couplers are necessary for the connection of various cylinders to one pump but are also important to
offer an axial rotating possibility for the connected cylinder.
Yale hydraulic couplers are self-sealing which means that the coupler halves only have to be closed hand tight.
|
|
 |
Pressure Gauges
The use of pressure gauges is recomended when the operating pressure (the force of the connected cylinder) should be monitored.
|
|
 |
GYA-63 Pressure Gauge Set
This pressure gauge set is suitable for connection to all HPS hand pumps. Assembled ready to use,
compact design with 45° inclination for easy reading. Consisting of pressure gauge GGY-632 and corresponding gauge adaptor.
|
|
 |
GA-700/701 - Pressure Gauge Adaptor
These pressure gauge adaptors are suitable for connection to all HPS hand pumps. Gauge connetion with sleeve nut and 30°
inclination for easy reading.
GA-700 for small pressure gauges
GA-701 for large pressure gauges.
|
|
 |
GA-703 - Pressure Gauge Adaptor Set
This pressure gauge adaptor set is suitable
for connection to all HPH hand pumps (for double acting cylinders). To be connecteed between 4-way valve and hand pump.
|
|
 |
GA-2000 - Pressure Gauge Adaptor
This pressure gauge adaptor is suitable for connection
to all TWZ hand pumps (2000 bar). With 30° inclination for easy reading. Suitable for pressure gauge GGY-2500.
|
|
 |
AYL - Tilt Saddles for YEL and YEG Series
Tilt saddles should be used with YEL and YEG cylinders in cases where cylinders are operated on non-parallel surfaces.
The saddles minimise inner friction caused by eccentric loading of the cylinders. The upper part of the saddle can pivot
up to 5° in all directions.
Tilt saddles are fixed in the position by means of an o-ring.
|
|
 |
AYH - Clevis Eye Mountings
Clevis eye mountings are screwed onto the piston and bottom of the
hydraulic cylinder in those cases where mounting conditions require a pivoting of the cylinder.
|
|
|
For further information or to request a quotation please contact
sales@lifting-safety.co.uk
To assist us in responding quickly to your enquiry please always include relevant information
on your enquiry such as SWL, Height of Lift and where required Electricity phase.
Thank You
|
GYA-63 Pressure gauge set